b'READY HYDROCAMH-2 PiercingForming Unit Specs. (cont.)Model Model Model Model Model Model ModelH-2 3.2 5 7.8 12.5 20 312Metric Force Per Unit 2 ton 3.2 ton 5 ton 7.8 ton 12.5 20 ton 31 ton NOTE: De-rated Force equalsDe-rated Force daN 1787 2885 4545 7094 11,319 18,819 28,817 maximum force less standardlbf. 3932 6346 10,002 15,611 24,906 41,440 63,439 (minimum) return force.VC Volume/str.(mm) cm 3 0.491 0.804 1.257 1.963 3.117 5.027 7.854 See H-2 dimension chart oninch 3 0.0300 0.0491 0.0767 0.1198 0.1902 0.3067 0.4793 previous page. All figures areMax Force at 400 bar daN 1,963 3,198 4,998 7,801 12,473 19,998 30,997 nominal unless tolerance is(5802 PSI) lbs. 4,328 7,050 11,020 17,200 27,500 44,090 68,340 stated. P-cm 3 12.27 20.11 31.42 49.09 77.93 125.66 196.35 Forces are rated in metricVolume (stroke 25 mm) inch 3 0.749 1.227 1.917 2.995 4.756 7.668 11.982 tons (1 metric ton = 1.1Volume (stroke 50 mm) cm 3 24.54 40.21 62.83 98.17 155.86 251.33 392.70 U.S. ton)inch 3 1.498 2.454 3.834 5.991 9.511 15.337 23.964Volume (stroke 75 mm) cm 3 N/A 60.32 94.25 147.26 233.79 376.99 589.05inch 3 3.681 5.751 8.986 14.267 23.005 35.946Volume (stroke 100 mm) cm 3 N/A N/A N/A N/A 311.72 502.65 785.40inch 3 19.023 30.674 47.928Standard Min. Return ForcedaN 176 313 453 707 1,154 1,179 2,180at 100 bar (1,450 PSI) lbf. 396 704 1,018 1,589 2,594 2,650 4,901Max. Return ForcedaN 265 470 679 1,061 1,731 1,768 3,270at 150 bar (2,175 PSI) lbf. 596 1,056 1,526 2,385 3,891 3,975 7,351L2 L3 L2 D6 L3 N 2 Inlet Port D6 N 2 Inlet PortL2 L3L2 L3 D6 N 2 Inlet PortD6 N 2 Inlet Port Option: Option:Direct Round Direct RoundOption:Option:Punch MountingPunch Mounting Direct RoundDirect Round limits on punch (Note:limits on punch(Note:Punch Mounting shank diameter)Punch Mountingshank diameter)in in in in (Note:limits on punch +0.5 mmmm mm mm mm(Note:limits on punchin mm in in 0.008 0.02 0.0008 G 0.2 0.008 0.02 0.0008 G D4 shank diameter) D4Vent Screw Vent Screw +0.02 in.shank diameter)in 0.2 Vent Screw L1mm mm mm + + + + + + + +0.2 + 0.2 0.008 + 0.008 0.02 + 0.02 0.0008 + 0.0008 B1 B2 B1 B2 D4 D4G Vent ScrewGL8 L9+ + + +B1 B1 B2 B2D8 D8D8D8+0.02 mm +0.02 mmL4 +0.0008 in D2 L4 +0.0008 in D2+0.02 mm Front ViewL4+0.02 mm Direct PunchL4 +0.0008 in D2+0.0008 in D2 (enlarged view) Optional DirectTop View Punch Mount+0.5 mm +0.5 mmL1 +0.020 in L1 L6 0.020 in L6+0.5 mm +G - Oil L1 +0.5 mm L6 D5 D5L1 +0.020 in L6G - Oil+0.020 inG - Oil Supply Port Supply Port D5 D9 D9G - Oil D5Supply PortSupply Port D9D9in mm in 0.008 mm 0.5 in 0.008 3 30.5 mm + 0.5 mm in 0.008 + 0.008 + 0.5 1 + + 1 + mm in 2 D1 mm in 2 D1 3 3 Ht Ht+ 1 + Ht Ht mm mm in in 2 2 + 0.02 + 0.0008 D1 D1 Ht + 0.02 + 0.0008 Ht Ht Ht1 Ht 2x D3 2x D3Ht 0.02 + 0.02 0.0008 + 0.0008 Ht Ht2x D3D7 Piston D7 Piston 2x D3 (B2) (B2)+ +L7 D7 Piston L5 L5 (B2)D7 Piston L7 Standard: Standard:L7 L5 Front Mounting Plate(B2) B3 B3L7 L5 Standard: Front Mounting Plate Standard: B3Front Mounting PlateB3Front Mounting PlateFront ViewSide View Standard Front Plate(plate is machinable)7'